LPWS Basic Knowledge Practice Exam

These questions are part of the practice quiz. Start practicing

• Which procedure is conducted to calibrate the mount azimuth and alignment?
• Which unit is used to express the muzzle velocity of the M940 round?
• Which standard provides a quality management framework for consistent products and continuous improvement in LPWS?
• What component is commonly referred to as the 'brain' of the system?
• What is the exact code to pull detailed data for SOTs?
• What does traceability mean in LPWS?
• What is the TM for the system?
• What is the nomenclature of the gun?
• What window do you open in WINPASS?
• How should frequently used equipment be maintained?
• What does SOT stand for?
• WP 34 is a procedure conducted to perform what?
• How often is the WADS supposed to change over?
• How is the system cooled?
• Which item is not typically included in a basic first aid kit for LPWS?
• Why is redundancy important in safety systems?
• What is the minimum number of legs that must be flown to complete sensor registration?
• The LPWS defended area is what distance?
• Why is housekeeping important in a workshop?
• What is the nickname for the protective enclosure in this setup?
• What does GD&T stand for in blueprint reading?
• Which component is essential for handling sensitive documents to track changes over time?
• Which of the following is NOT a component of the I2N?
• Which of the following generator frequency values is used in the system?
• Who is the FLIR picture for?
• Which sequence correctly represents the steps in a basic risk assessment?
• Before performing a PAC-Fire, which PSOT is typically run?
• What must be off before you go to stand by?
• Which statement about the search sector is false?
• The term 'Generator Set' refers to which assembly?
• Why is cybersecurity important in LPWS?
• Which three items must be checked or serviced during daily maintenance?
• What tool is used to stop the rounds from moving into the firing path?
• Which action best verifies that a control measure is effective?
• Which option correctly states the two radar capabilities?
• The acronym DNES refers to which sector?
• Document control encompasses which of the following functions?
• On what basis should PPE be selected in LPWS?
• What does PRCS stand for?
• The ballast serves as a counterweight for FLIR and EOSS assembly.
• What does data integrity mean and why is it critical?
• Who must approve troubleshooting actions?
• Which combination matches the radar's search sector?
• What computer program do you start?
• Which option describes the generator setup used to power the mount?
• How should supplier quality be evaluated in LPWS?
• Which circuit breaker is pulled to stop mount movement?
• What wattage is the generator typically set to?
• Which component is housed in the electronics enclosure?
• Which display shows real-time LPWS radar feedback, known aircraft, and confirmed RAM data?
• Which action best supports maintaining energy isolation during maintenance?
• Which device is used to stop rounds entering the firing path?
• How is a quality defect typically classified in LPWS?
• What is the purpose of maintaining equipment labels over time?
• Which statement accurately describes the M940 round?
• What code do you run to get back power?
• Which maintenance approach is based on monitoring equipment condition to schedule maintenance before failure?
• Which of the following is a described capability of the PRCS in relation to LPWS?
• What does ELX stand for?
• What are the radars?
• What additional measures are required in chemical hygiene besides PPE?
• What is the purpose of a permit system in LPWS?
• The FLIR image is intended for which authority to help prevent fratricide?
• What should be included in a basic first aid kit in LPWS?
• Identify a noncomponent option that is NOT part of the I2N.
• Troubleshooting actions require whose approval?
• Which statement about Safety Data Sheets (SDS) is correct?
• How should sensitive or perishable documents be handled?
• PSOT 14 is designed to test which gun parameter?
• PSOT 22 is necessary to conduct what type of engagements?
• What maintenance step helps prevent damage from wet-stacking in LPWS generators?
• What goes under the FLIR?
• How should waste be segregated?
• What does GHS stand for and why is it important?
• Which elevation value defines the radar's search sector?
• What does a chemical hygiene program involve?
• What generators do we use?
• What is the temperature range of the chiller?
• What is the nomenclature for the round?
• ___________ is conducted to calibrate the mount azimuth and alignment.
• ISO 9001 relates to LPWS by providing a quality management framework to ensure what?
• How should equipment be labeled?
• Which statement best describes lockout/tagout (LOTO) in an industrial setting?
• How is the mount powered?
• Which sequence describes a typical startup sequence?
• Which PSOT is run before a PAC-Fire?
• Why is labeling important when segregating waste?
• What is the purpose of a control chart in LPWS?
• How many SOTS are run for dailies?
• Which of the following is NOT typically included in a daily start-up checklist for LPWS?
• What is the round size?
• What does PSOT 14 do?
• What is the muzzle velocity of the M940 round?
• What is the purpose of documenting alarm events and performing root-cause investigations?
• What does PAC stand for?
• Which statement about ballast is true?
• Alarm management involves which activities?
• What is ergonomics and why is it important in LPWS?
• How many radars are there?
• Which items should be included in a daily start-up checklist for LPWS?
• Which technique reduces back injury when lifting a load?
• Which configuration describes the mount’s power generation setup?
• What is the initial action to take upon receiving a fault?
• How many components are in the I2N?
• Why is load bank testing important for LPWS generators?
• What test fire is run after a PAC-fire?
• The LPWS defended wall altitude maximum is 900 meters, which corresponds to which option?
• When disposing chemical waste, which practice is essential?
• Which two components are used to separate and stabilize the barrels?
• What solution is used in the chiller?
• Which statement about PRCS is true?
• How should you respond to a chemical spill if you are trained to handle it?
• Which statement best describes the purpose of an SOP?
• SOTs 1-7 refer to which subsystem?
• What is the risk of noise exposure and how can it be mitigated?
• What is the brain of the system?
• What is the maximum range of the LPWS?
• Which of the following describes a component of the I2N?
• Which list correctly identifies the four components of the I2N?
• In a startup sequence, which option lists the correct order?
• Which constitutes effective team communication?
• Which of the following is a component of the I2N?
• When is a permit-to-work required?
• Which of the following best describes the purpose of a permit system in LPWS?
• Sensor Registration ensures that reported track positions are correct and correlate with reporting sources.
• What code pulls detailed data for SOTs?
• Which of the following describes a capability of the PPI display?
• In LPWS, what best defines a near miss?
• Sensor Registration is an important process that calibrates radars and Phalanx Weapon Systems to ensure that reported track positions are correct and correlate with all reporting sources. Which statement best reflects this?
• What is the difference between calibration and validation?
• What frequency are the generators set to?
• Which statement best describes the system's mode of operation with oversight?
• What is the purpose of lockout/tagout (LOTO) in LPWS?
• Which statement best describes how traceability supports product safety?
• What is the name of the crane used to lift the EOSS?
• Which PPE is typically required when handling chemicals in LPWS?
• Which statement correctly differentiates preventive and predictive maintenance?
• What is change control?
• From what sources can we get power?
• How is the system operated?
• What is the function of the ballast?
• What is this type of cooling system called?
• What is the designation of the round?
• What is the search sector for the LPWSs Search Radar?
• What does FLIR stand for?
• What should you do if a fire alarm sounds in LPWS?
• What is energy isolation in maintenance?
• What does the gun sit on?
• After documenting an incident, what is the next best action?
• Which component serves to stabilize the electro-optical payload?
• Which maintenance approach uses condition data to anticipate failures and schedule repairs?
• Which option lists the chiller coolant solution?
• Which of the following is true about the generator wattage setting mentioned?
• Which item is essential for daily maintenance checks on the LPWS control panel?
• What is a basic electrical safety practice?
• How many barrels does the gun have?
• How is a confined space defined in LPWS?
• How should chemical waste be disposed of in LPWS?
• Within WINPASS, which window is used for terminal-type access?
• What is document control?
• What does Sensor Registration produce for the LPWS in relation to sensors and the EOC?
• How should incident reporting be documented?
• Which component is used to lift the EOSS?
• What are the correct steps in a basic risk assessment?
• Which of the following expresses the elevation limits most accurately?
• What is the cage called?
• What code can change the ammo count within the system?
• Which practice supports maintaining safety and quality when updating equipment?
• The LPWS defended altitude maximum is what value?
• What is Root Cause Analysis and a common method?
• What is a lock-out/Tag-out device?
• Which list includes only the four I2N components?
• How many bars does the sensor radar have?
• What two methods are used for destroying classified equipment?
• What is the end product of sensor registration?
• What is the fire rate?
• What three actions are performed prior to running a PSOT?
• What information does an SDS provide?
• What does DNES stand for?
• What CB is pulled to stop mount movement?
• How does traceability support product safety?
• What are the elevation limits?
• WP 34 is conducted to perform what?
• Which statement describes the relationship between redundancy and safety?
• Which statement best describes the difference between a hazard and a risk?
• The fire rate equals 4500 rounds per minute. Which of the following is equivalent in rounds per second?
• Which elements are essential when reading a blueprint in LPWS?
• Which two components' combined function is to separate and stabilize the barrels?
• Which azimuth value defines the radar's search sector?
• How many rounds can the drum hold?